Durability performance of alkali-activated concretes exposed to sulfuric acid attack


  • Anıl Niş Department of Civil Engineering, Istanbul Gelisim University, Istanbul (Turkiye)
  • Melis Bilenler Altundal Department of Civil Engineering, Istanbul Gelisim University, Istanbul (Turkiye)




Geopolymer concrete (GPC), alkali activated slag (AAS), alkali activated fly ash/slag (AFS), alkali activated materials, sulfuric acid attack.


In this research, chemical durability performances of the alkali-activated slag (AAS), 50% ground granulated blast furnace slag and 50% fly ash (AFS), ordinary Portland cement (OPC), and geopolymer (GPC) concretes were investigated thoroughly under 5% sulfuric acid attack. All alkali-activated concrete specimens were produced considering the minimum binder content of 360 kg/m3 and the maximum alkali activator to binder ratio of 0.45 according to the XA3 environment given in EN 206-1 standard for OPC concrete. The visual inspection, weight change and compressive strength tests were performed to understand the influence of sulfuric acid attack on the resulting performances. Also, scanning electron microscope (SEM) and energy dispersive X-ray spectrometry (EDS) analyses were performed to examine the morphological variations in micro-scale. The mechanical performances and durability of alkali-activated concretes were also compared to the OPC concrete for structural utilization. The results revealed that AFS specimens showed the best durability, while GPC specimens exhibited the poorest durability. SEM/EDS results pointed out that AFS specimens exhibited denser and less porous microstructure, and the reductions in Al/Si and Ca/Si atomic ratios were observed under 5% sulfuric acid attack. In contrast, GPC specimens showed less dense and porous microstructure, and high aluminum leaching was observed. In addition, the wider interconnected macro cracks and high calcium leaching were observed in the AAS samples under 5% sulfuric acid attack. Finally, the AAS and AFS specimens can be utilized in structural applications, while GPC specimens should not be used with a minimum binder content proposed by EN 206-1 standard.


Albitar, M., Ali, M. M., Visintin, P., & Drechsler, M. (2017). Durability evaluation of geopolymer and conventional concretes. Construction and Building Materials, 136, 374-385.

Allahverdi, A., & Skvara, F. (2001). Nitric acid attack on hardened paste of geopolymeric cements, Part 1. Ceramics Silikaty, 45(3), 81-88.

Allahverdi, A., & Skvara, F. (2005). Sulfuric acid attack on hardened paste of geopolymer cements-Part 1. Mechanism of corrosion at relatively high concentrations. Ceramics Silikaty, 49(4), 225.

Al-Majidi, M. H., Lampropoulos, A., Cundy, A., & Meikle, S. (2016). Development of geopolymer mortar under ambient temperature for in situ applications. Construction and Building Materials, 120, 198-211.

ASTM C39/C39M-01. (2003). Standard test method for compressive strength of cylindrical concrete specimens. Am. Soc. Test. Mater. West Conshohocken, USA.

ASTM, C618-03. (2003). Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.

Attiogbe, E. K., & Rizkalla, S. H. (1988). Response of concrete to sulfuric acid attack. ACI materials journal, 85(6), 481-488.

Aygormez, Y. (2021). Sulfuric acid effect and application of freezing-thawing curing on long fiber reinforced metabentonite and slag-based geopolymer composites. Advances in concrete construction, 12(2), 145-156.

Aygormez, Y., & Canpolat, O. (2021). Long-term sulfuric and hydrochloric acid resistance of silica fume and colemanite waste reinforced metakaolin-based geopolymers. Revista de la construcción, 20(2), 291-307.

Bakharev, T. (2005). Geopolymeric materials prepared using Class F fly ash and elevated temperature curing. Cement and concrete research, 35(6), 1224-1232.

Bassuoni, M. T., & Nehdi, M. L. (2007). Resistance of self-consolidating concrete to sulfuric acid attack with consecutive pH reduction. Cement and Concrete Research, 37(7), 1070-1084.

Benhelal, E., Zahedi, G., Shamsaei, E., & Bahadori, A. (2013). Global strategies and potentials to curb CO2 emissions in cement industry. Journal of cleaner production, 51, 142-161.

Bondar, D., Lynsdale, C. J., Milestone, N. B., Hassani, N., & Ramezanianpour, A. A. (2011). Effect of type, form, and dosage of activators on strength of alkali-activated natural pozzolans. Cement and Concrete Composites, 33(2), 251-260.

Chang, Z. T., Song, X. J., Munn, R., & Marosszeky, M. (2005). Using limestone aggregates and different cements for enhancing resistance of concrete to sulphuric acid attack. Cement and Concrete Research, 35(8), 1486-1494.

Chi, M., & Huang, R. (2013). Binding mechanism and properties of alkali-activated fly ash/slag mortars. Construction and Building Materials, 40, 291-298.

Çevik, A., Alzeebaree, R., Humur, G., Niş, A., & Gülşan, M. E. (2018). Effect of nano-silica on the chemical durability and mechanical performance of fly ash based geopolymer concrete. Ceramics International, 44(11), 12253-12264.

Džunuzović, N., Komljenović, M., Nikolić, V., & Ivanović, T. (2017). External sulfate attack on alkali-activated fly ash-blast furnace slag composite. Construction and Building Materials, 157, 737-747.

European Committee for Standardization. EN 206–1:2013, Concrete—Specification, Performance, Production and Conformity; CEN: Brussels, Belgium, 2013.

Fernández-Jiménez, A., Palomo, A., & Criado, M. (2005). Microstructure development of alkali-activated fly ash cement: a descriptive model. Cement and concrete research, 35(6), 1204-1209.

Gao, K., Lin, K. L., Wang, D., Hwang, C. L., Shiu, H. S., Chang, Y. M., & Cheng, T. W. (2014). Effects SiO2/Na2O molar ratio on mechanical properties and the microstructure of nano-SiO2 metakaolin-based geopolymers. Construction and Building Materials, 53, 503-510.

Golewski, G. L., & Sadowski, T. (2017). The fracture toughness the KIIIc of concretes with F fly ash (FA) additive. Construction and Building Materials, 143, 444-454.

Imbabi, M. S., Carrigan, C., & McKenna, S. (2012). Trends and developments in green cement and concrete technology. International Journal of Sustainable Built Environment, 1(2), 194-216.

Ibrahim, M., Johari, M. A. M., Rahman, M. K., & Maslehuddin, M. (2017). Effect of alkaline activators and binder content on the properties of natural pozzolan-based alkali activated concrete. Construction and Building Materials, 147, 648-660.

Ismail, I., Bernal, S. A., Provis, J. L., San Nicolas, R., Hamdan, S., & van Deventer, J. S. (2014). Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash. Cement and Concrete Composites, 45, 125-135.

Jang, J. G., Lee, N. K., & Lee, H. K. (2014). Fresh and hardened properties of alkali-activated fly ash/slag pastes with superplasticizers. Construction and Building Materials, 50, 169-176.

Juenger, M. C. G., Winnefeld, F., Provis, J. L., & Ideker, J. H. (2011). Advances in alternative cementitious binders. Cement and concrete Research, 41(12), 1232-1243.

Komljenović, M., Baščarević, Z., Marjanović, N., & Nikolić, V. (2013). External sulfate attack on alkali-activated slag. Construction and Building Materials, 49, 31-39.

Kumar, R., Kumar, S., & Mehrotra, S. P. (2007). Towards sustainable solutions for fly ash through mechanical activation. Resources, Conservation and Recycling, 52(2), 157-179.

Kumaravel, S., & Girija, K. (2013). Acid and salt resistance of geopolymer concrete with varying concentration of NaOH. Journal of Engineering Research and Studies, 4(4), 1-3.

Kurtoglu, A. E., Alzeebaree, R., Aljumaili, O., Nis, A., Gulsan, M. E., Humur, G., & Cevik, A. (2018). Mechanical and durability properties of fly ash and slag based geopolymer concrete. Advances in Concrete Construction, 6(4), 345-362.

Lee, N. K., Jang, J. G., & Lee, H. K. (2014). Shrinkage characteristics of alkali-activated fly ash/slag paste and mortar at early ages. Cement and Concrete Composites, 53, 239-248.

Li, S., & Roy, D. M. (1988). Preparation and characterization of high and low CaO/SiO2 ratio “pure” C–S–H for chemically bonded ceramics. Journal of Materials Research, 3(2), 380-386.

Li, Z., & Ding, Z. (2003). Property improvement of Portland cement by incorporating with metakaolin and slag. Cement and Concrete Research, 33(4), 579-584.

Ma, C. K., Awang, A. Z., & Omar, W. (2018). Structural and material performance of geopolymer concrete: A review. Construction and Building Materials, 186, 90-102.

Marjanović, N., Komljenović, M., Baščarević, Z., Nikolić, V., & Petrović, R. (2015). Physical–mechanical and microstructural properties of alkali-activated fly ash–blast furnace slag blends. Ceramics International, 41(1), 1421-1435.

Mehta, A., & Siddique, R. (2017). Sulfuric acid resistance of fly ash based geopolymer concrete. Construction and Building Materials, 146, 136-143.

Niş, A., & Altındal, İ. (2021). Compressive Strength Performance of Alkali Activated Concretes under Different Curing Conditions. Periodica Polytechnica Civil Engineering, 65(2), 556-565.

Palomo, A., Grutzeck, M. W., & Blanco, M. T. (1999). Alkali-activated fly ashes: a cement for the future. Cement and concrete research, 29(8), 1323-1329.

Part, W. K., Ramli, M., & Cheah, C. B. (2015). An overview on the influence of various factors on the properties of geopolymer concrete derived from industrial by-products. Construction and Building Materials, 77, 370-395.

Patil, A. A., Chore, H. S., & Dodeb, P. A. (2014). Effect of curing condition on strength of geopolymer concrete. Advances in concrete construction, 2(1), 29-37.

Provis, J. L., Myers, R. J., White, C. E., Rose, V., & van Deventer, J. S. (2012). X-ray microtomography shows pore structure and tortuosity in alkali-activated binders. Cement and Concrete Research, 42(6), 855-864.

Puertas, F., Martı́nez-Ramı́rez, S., Alonso, S., & Vazquez, T. (2000). Alkali-activated fly ash/slag cements: strength behaviour and hydration products. Cement and Concrete Research, 30(10), 1625-1632.

Reddy, M. S., Dinakar, P., & Rao, B. H. (2018). Mix design development of fly ash and ground granulated blast furnace slag based geopolymer concrete. Journal of Building Engineering, 20, 712-722.

Ridtirud, C., Chindaprasirt, P., & Pimraksa, K. (2011). Factors affecting the shrinkage of fly ash geopolymers. International Journal of Minerals, Metallurgy, and Materials, 18(1), 100-104.

Ryu, G. S., Lee, Y. B., Koh, K. T., & Chung, Y. S. (2013). The mechanical properties of fly ash-based geopolymer concrete with alkaline activators. Construction and Building Materials, 47, 409-418.

Soutsos, M., Boyle, A. P., Vinai, R., Hadjierakleous, A., & Barnett, S. J. (2016). Factors influencing the compressive strength of fly ash based geopolymers. Construction and Building Materials, 110, 355-368.

Tavasoli, S., Nili, M., & Serpoosh, B. (2018). Effect of GGBS on the frost resistance of self-consolidating concrete. Construction and Building Materials, 165, 717-722.

Temuujin, J. V., Van Riessen, A., & Williams, R. (2009). Influence of calcium compounds on the mechanical properties of fly ash geopolymer pastes. Journal of hazardous materials, 167(1-3), 82-88.

Thokchom, S. (2014). Fly ash geopolymer pastes in sulphuric acid. Int. J. Eng. Innovation Res, 3(6), 943-947.

TS13515 (2012). Complementary standard for application of TS EN 206-1.

Wardhono, A., Gunasekara, C., Law, D. W., & Setunge, S. (2017). Comparison of long term performance between alkali activated slag and fly ash geopolymer concretes. Construction and Building materials, 143, 272-279.

Winnefeld, F., Leemann, A., Lucuk, M., Svoboda, P., & Neuroth, M. (2010). Assessment of phase formation in alkali activated low and high calcium fly ashes in building materials. Construction and building materials, 24(6), 1086-1093.

Wongpa, J., Kiattikomol, K., Jaturapitakkul, C., & Chindaprasirt, P. (2010). Compressive strength, modulus of elasticity, and water permeability of inorganic polymer concrete. Materials & Design, 31(10), 4748-4754.

Zhang, W., Yao, X., Yang, T., & Zhang, Z. (2018). The degradation mechanisms of alkali-activated fly ash/slag blend cements exposed to sulphuric acid. Construction and Building Materials, 186, 1177-1187.




How to Cite

Niş, A., & Altundal , M. B. . (2023). Durability performance of alkali-activated concretes exposed to sulfuric acid attack. Revista De La Construcción. Journal of Construction, 22(1), 16–35. https://doi.org/10.7764/RDLC.22.1.16

Most read articles by the same author(s)

Obs.: This plugin requires at least one statistics/report plugin to be enabled. If your statistics plugins provide more than one metric then please also select a main metric on the admin's site settings page and/or on the journal manager's settings pages.